Jon N from the UK sent me an interesting find, pictures of a LeRun Jr. I did not know a junior model existed. Notice the Jr uses a traditional bicycle seat, unlike the regular model with a unicycle seat.
The LeRun Jr comes from Winson Ooi of Petaling Jaya, Malaysia. He posted these photos on KELAB BASIKAL LAMA, a Facebook bicycle club to share their collections of bicycles owned.
The “thebigfatlittleshoppe” in Singapore is showing this pretty red LeRun Jr.
I purchased the Garel from eBay thinking it was a Lerun skatebike, the previous owner had made some alterations to the front and replaced the original truck with a newer and poorly fitting skateboard truck. The skateboard wheels were dry and cracked with one coming off on the first try riding it, the rear wheel didn’t sit correctly under the frame and the spokes were bent and needed attention. (See part 1)
I took the skateboard truck off and switched it with a Continental skateboard truck that I purchased from eBay mounted on an old Penny board. The hole spacing for the truck to be mounted to the Garel is the same as the Lerun and Max, for finding a replacement I would recommend old Penny boards made by companies like Variflex, Skuda and Super Star if you are on a budget as they can be picked up quite cheaply, alternatively higher end models by companies like Vulcan and ACS-430 also appear to have the correct spacing but always double check with the vendor before you buy it. With the Conti fitted I installed two Deville Whitewalls 70mm / 78A and would highly recommend them to anyone. My attention then turned to the rear wheel whereby I took it to a local bike shop where they managed to true the rim, the next change was to the tyre and switching from an old and degraded one and to a newer whitewall I had taken from elsewhere. I put some washers in place on the rear axle and managed to line up the wheel to be under the frame which in turn would improve the stability. I then switched the quick release seat-post clamp to a fixed one to improve the lines of the design and eliminate the risk of someone pinching the seat if it was locked up outside a shop.
Riding the Garel after these modifications it was clear how the changes vastly improved the riding experience, it is stable and smooth rolling and a pleasure to ride!
Lastly I changed the colour to Chromacoat Peacock (available through Kustom Canz suppliers) as the original green had chipped and rubbed off in various places (I did buy a can of a very similar green before I started just in case it didn’t work out and I wanted back the way it was). There are lots of colours to pick from and I wanted something that would appear as a different colour from different angles and Kustom Canz do a kit of 3 cans consisting of base coat, main colour and the top clearcoat, alternatively you can just go for the main colour if you wish. I removed the truck, rear wheel, chain and seat-post clamp but left the crank arms, pedals and bottom bracket on (it is a Cottered crank and I didn’t want to risk damaging it trying to remove it) and masking taped them to be ready for spraying. I then removed the Garel sticker from the frame and sanded down the frame to ensure it was smooth before applying primer. The primer went on without issue and I checked to see if there were any sections that needed attention before adding a base coat. I gave the primer a light sanding with some 2000 grit paper and a clean down before applying a black base coat in order to help the main colour stand out. I then gave it another quick sanding with 2000 grit again and then went on with the Peacock colour, which like most spraying is better done in multiple lighter coats rather than 2 thick ones. Make sure you are spraying in a very well ventilated area and use a mask as this has a very powerful odour and harmful chemicals, even outdoors wear a mask for it! Once the main colour was dry I applied multiple coats of a clear finish to protect it, once that was dry I reattached the wheels and chain (I had sprayed the seat-post separately).
The Garel rides great and looks even better and is a far cry from how it was when I originally received it, I might change the colour again at some point and go for another variation but I’ll keep it like this over summer as the sun highlights how vibrant it is.
By Jon N. – UK
I purchased this Max skatebike from Facebook marketplace with the intention of giving it a go and seeing what happens and ended up becoming obsessed with it and making little design changes to it along the way.
I started off by changing the seat-post and seat as the seat-post was too short for me at 250mm long (Changing LeRun/Garel/Max Skatebike Seat/Saddle), once the unicycle seat was installed it made riding it considerably easier and more comfortable.
The next change was to spray the rear wheel black to match the frame and change the overall feel of it. It was a simple case of taking the wheel out and removing the tyre and tube then masking off the metal sections to leave only the yellow plastic visible and then spray. I would advise using a primer first and then your colour and then a protective clear coat on top, I went straight for black without a primer and didn’t put a clear coat on after and it has come away in a couple of small sections so will probably need a respray at some point.
Once the spraying was done the next change was to the tyre and I installed a Kenda ‘whitewall’ tyre, to me the colour contrast works really well and matches the seat colouring. The tread on the whitewall is aimed more at roads as opposed the original tyre that had a deeper tread pattern aimed at muddier terrain. The width of the Kenda is slightly less than the original but this does not negatively affect the riding experience.
The seat post clamp was then switched to a fixed clamp rather than a quick release, this aspect is also covered further in the article on changing the seat. The chain that was on there originally had seen better days so I thought why not get a gold chain for it? As a further little touch I bought four dice valve covers and added one to keep it colour coordinated. I also sprayed the crank arms and sprocket black as the chrome would have stood out. I had also changed the truck bushings to 94A by this point to aid the turning ability.
Lastly were the front wheels, originally it had Kryptonics 70mm installed (not sure of the firmness rating), these were great for different road surfaces and small pebbles and sticks but were not in keeping with the colour scheme and I wanted to go for something at the soft end of the scale to see if there was a difference. I opted for Deville Whitewalls 70mm and 78A rating and they are fantastic! They feel very smooth out on roads and paving slabs and wonderful on smoother surfaces.
In terms of how the impact of the changes in functional terms the largest would be changing the seat-post and the bushings and the front wheels, the aesthetic colour changes influenced how I saw the skatebike and allowed me to put my mark on it.
The Max rides fantastically and whilst it looks very different to how it arrived it has developed into something I am very proud of and I hope it inspires people and shows what is possible with a little TLC.
Minson skatebikes use standard “Old School” skateboard truck hole pattern.
Garel, LeRun and Max skatebikes use a smaller pattern
AXL skatebikes use a third hole pattern
AXL trucks are plastic rather than cast aluminum like the other skatebikes.
This is an AXL skatebike that Jon N from the UK bought. One of the wheels came apart on his first ride. Because the hole pattern is so small he could not fit any of the old skateboard trucks. The axel hanger from an old 70’s Continental skateboard truck fit.
May 19, 2021 update
Jon also found this old Tony Hawk skateboard in second hand shop. The holes are very close and for not much money he got 2 trucks, 4 wheels and 8 bearings.
Jon N. from the UK wrote this article about changing the seat on his Max Skatebike to a unicycle seat. My personal skatebike is a Minson which uses a traditional seat post and seat. The Garel/LeRun/Max skatebikes use a unicycle like seat connection.
BTW: A unicycle seat is often referred to as a unicycle saddle.
The skatebikes used in the photos are a black Max skatebike and a blue LeRun, the LeRun and the original Max seat are the same design and are shown for comparison purposes. When I purchased my Max skatebike from eBay the seat post was too short for me to ride in a comfortable position. The post was 250mm long which once you’ve taken into account the section required to go into the frame it did not leave a lot the space required for a person just over 6 foot tall like myself. I had hoped to simply replace the seat post with a longer one and all would be fine, however when I examined the fixing of the post to the seat I realised the seat itself had 3 shafts for nuts and were positioned in a triangular shape. I searched online and couldn’t find a replacement seat post that had triangular hole positioning so I decided to replace the seat too. The fixings on most bicycle seat posts are designed to work at an angle and for a skatebike it needs to be straight up which is how I arrived at a unicycle seat and post.
I used unicycle.com who had a good selection of seats and posts along with other supplies. The seat post width for my Max is 25.4mm (Lerun and Garel models use 25mm), I went for a 350mm long post and a zebra print seat for a total of £30. There are other colour variations out there but as soon as I saw this I knew it was the one for me! As you can see there are differences in the designs of the original seat and the unicycle seat, namely the width is reduced on the unicycle seat and the curve angle is increased on this ‘freestyle’ seat (flat unicycle seats are available on the website too). The unicycle seat is firmer than the original from the Max and is fixed to the seat post via 4 shafts in a rectangular formation and allows for tweaks on the angle of the seat rather than the fixed position of the original seat. The grab section at the front (there is also a grab section at the rear of the unicycle seat) is incorporated into the seat design rather than the ring design of the original, this can take a little getting used to at first if you’ve been using a ring for a long time. When I first put the unicycle seat on and went out on it I really noticed the width difference compared to the original and was concerned that it would take something away from the comfort aspect however I found it is easier to understand where my body weight is in terms of positioning. The original seat is wider and in comparison feels almost too wide for me now and there’s less clarity in knowing where your centre of gravity is, however the original is more comfortable and has more of a shallow sideways C profile. From a top down view the unicycle seat is an hourglass shape which helps position the rider and the original is a teardrop shape. I would suggest trying one out in a shop if you can, I’m average build and a unicycle seat may not be comfortable for everyone.
Out of the two seats I would say I prefer the unicycle seat as I find it better for comfort, response and firmness. The original seat works as a seat but there are other options out there and it might change how you feel on a skatebike and grow your confidence to try more moves or go for longer distances so why not give it a try?
Another change I made to the Max was to the seat post clamp and removing the quick release system. I decided a fixed seat post clamp would be better for me for when I lock it up outside a shop I don’t have to worry someone can pinch the seat, plus it looks slicker to me and matches in terms of colour. It was a simple case of taking off the quick release fitting and popping the fixed seat clamp post (I sprayed it black as it was chrome – 28.6mm seat post clamp for Max/Lerun/Garel) and tightening it accordingly.
Jon N. – UK
Most skatebikes use a skateboard truck up front for steering. There is nothing special about the truck except the choice of wheels and bushings. Assuming you are looking at a Minson or a Garel/LeRun bike, you have 30+ year old rubber in the truck. The bushings and pivot bushing will be hard as a rock and the bearings probably need cleaning and greasing.
Worlds Of Wonder files for a US Trademark for “AXL Skatebike” on 1990-05-29
4209 Technology Drive, Fremont, CA 94538, USA
Serial Number: 74063815
1990-04-19: AXL Skatebike Press Release distributed
1990-05-29: Application Filed
1992-07-07: Published for Opposition
1993-03-30: Status: Dead/Abandoned
AXL Skatebikes appear to be a rebranded MAX Skatebike. A chain guard is added and the labels are changed. Both use a 12″ plastic wheel.
Lerun began its operations back in the 1970s, pioneering the manufacturing of mountain bikes for the local market. Lerun’s ‘claim to fame’ is the Skatebike – the one-wheel unicycle which was launched back in the late 80s. The introduction of the Skatebike created a cult following amongst youngsters and henceforth catapulted the Lerun Unicycle up to the top of every kid’s wish list. Since then, the Lerun brand has become a household name.
Headquartered at Puchong, Selangor, the Lerun head office controls all distribution and sales operations for its diverse portfolio of bicycles. The product range that is offered includes MTB, BMX, Tandem Bike, Folding Bike, City Bike and Racing Bikes with wheel sizes ranging from 16 inches to 26 inches, which are marketed under the popular “Lerun” and “Polygon” brands.
A pristine LeRun before the MTV branding.
Feb 8, 1988 – MTV announced their first licensing agreement, the MTV LeRun. The pact provides for an advertising campaign on MTV with retail sales to begin in Fall 1988.